XLERATOR^® Hand Dryers

• 
• 
• 
• 
• 
• 

Model No.	Cover Finish	Mounting	Time Cycle	Dryer Type
XL-BW	White Thermoset (BMC)	Surface	Automatic	Hand Dryer
XL-W	White	Surface	Automatic	Hand Dryer
XL-GR	Graphite	Surface	Automatic	Hand Dryer
XL-C	Chrome	Surface	Automatic	Hand Dryer
XL-SB	Brushed Stainless Steel	Surface	Automatic	Hand Dryer
XL-SI*	Custom Special Image	Surface	Automatic	Hand Dryer

*Note: Exclusive digital image technology allows for the addition of Company, School or Team logos with any color, design or a 'Green message'

FEATURES

• Dries Hands Completely in 10 to 15 Seconds
• Uses 80% Less Energy
• 95% Cost Savings vs. Paper Towels
• GREENSPEC^® Listed and Helps Qualify for LEED^® credits.
• Source Reduction Alternative
• Promotes Hygiene

SPECIFICATIONS

Dimensions:	11 3/4" LG. X 12 11/16" HIGH X 6 11/16" DEEP (298 MM LG. X 322 MM HIGH X 170 MM DEEP)
Weight:	16 LBS. (7.3 KGS.)

Construction

1. Hand dryer cover shall be a one-piece, heavy-duty, rib-reinforced, die-cast zinc alloy. It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically applied epoxy paint and fastened to a wall plate by two chrome plated tamper-proof bolts.
2. Hand dryer wall plate shall be equipped with (3) 7/8" (22 mm) diameter holes, one of which shall be suitable for use with surface conduit, for ease of wiring.
3. All internal hand dryer parts shall be coated according to Underwriters' Laboratories, Inc. requirements.
4. Entire mechanism shall be internally grounded.

Mechanism

1. Hand dryer motor shall be a series commutated through-flow discharge vacuum motor/blower (5/8 HP / 20,000 RPM) which provides air velocity of 16,000 LFM (linear feet per minute) at the air outlet and 14,000 LFM at the hands (4 inches [102 mm] below air outlet).
2. Hand dryer heating element (970 W) is constructed of Nichrome wire and mounted inside the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of up to 135°F (57°C) at a 72°F (22°C) ambient room temperature at the hands (4 inches [102 mm] below air outlet).
3. Hand dryer Control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are under the air outlet. There is a 35-second lockout feature if hands are not removed.

Limited Warranty

The hand dryer shall be guaranteed to be free from defects for a period of five (5) years. Warranty shall include factory performed labor as well as the repair or exchange of defective parts, at manufacturer's option.

Hand Drying Procedure

Please contact Excel at 413-525-4531 for Excel's recommended hand drying procedure.

Units are available as specified in:
110/120V	12.5 Amp	60 hz	1500 Watts
208 V	7 Amp	60 hz	1500 Watts
220/240V	6.5 Amp	50 or 60 hz	1500 Watts
277V	5.5 Amp	60 hz	1500 Watts

Suggested Mounting Height From Floor to Bottom of Dryer
Men	45" (114 cm)
Women	43" (109 cm)
Teenagers	41" (104 cm)
Children	35" (89 cm)
Handicapped	37" (94 cm)

SmartBIM

¹ This certificate applies to all XLERATOR models except XL-SB.
² This certificate only applies to model XL-SB.